The table saw is a must-have piece of equipment for any woodworker or DIYer. A good fence is essential if you want the best table saw.
We now come to the crucial question: How do you construct a table saw fence. It’s not as hard as you might think. In this article, well show you how to do it.
What Is A Table Saw Fence?
A table saw fence is an essential piece of equipment for woodworkers. This is a rail that runs parallel to your table saw’s blade. It allows you to securely guide your workpiece through it. A good fence is essential for ensuring accurate cuts.
Why Should You Use A Table Saw Fence?
- Accuracy Good fencing ensures accurate cuts.
- Safety A fence helps keep your hands away from the blade, which reduces the risk of injury.
- Convenience By using a fence, you can quickly
How To Build A Table Saw Fence. (Step By Step Process)
Building a table saw fence is not a difficult task, but it does require some basic carpentry skills. Heres how to do it:
Step 1: Gather All The Necessary Tools
You will need all the tools and materials necessary to build a table-saw fence. Heres what youll need:24 (longer than the depth of your table saw)- 1 pc
4 piece Wood screws-(8 cm deck screws)
A Jigsaw
A Tape measure
Screw-threaded rod and nut
Step 2: Measure The Table Dimension
The first step is to measure the dimensions of your table saw. It is important to measure the table’s width and depth, as well the distance between the fence and the blade.
Once you have measured these dimensions, you can use them to build your fence.
Next, cut the 24-inch board to the right size. You should cut the board to the same length as your table saw plus 3 cm.
Width-wise, the board should be 5 cm narrower than the width of your table saw.
Once you have cut the board to size, its time to start building the fence.
Step 3: Assemble The Fence Rail
The fence rail is the foundation of the fence and must be strong and reliable. Take your screw-threaded rod, nut, and attach them to one end of the board. This will be the rail’s mounting point.
Use your jigsaw to cut two notches in the board as shown in the diagram. Ensure that the notches are big enough to fit the rod and nut.
After you have made the notches, attach the rail to your board using your wood screws. Make sure that the screws are countersunk so that they dont protrude from the boards surface.
Step 4: Mount The Rail To The Table Saw
Now its time to mount the rail to the table saw. This is a straightforward process, but youll need to be careful and precise.
Measure and mark the rail position on your table saw. Next, you will need to drill a pilot hole for the table saw. Next, insert the screws using your screwdriver. Then, use your wrench to tighten the screws.
Step 5 – Secure The Fence
Now it is time to attach the fence to the rail. This is an important step, so take your time and be careful.
First, use a screwdriver to loosen the screws on the fence. Next, tighten the screws by using your wrench. Next, tighten the screws on the rail with your wrench. Finally, tighten it again using your screwdriver.
And youre done! Now your table saw fence has been completed. Enjoy!
So, there you have it: a simple guide on how to build a table saw fence. Its not difficult, but it does require some basic carpentry skills. This guide will help you build a fence for your tablesaw, or to find out how to do it yourself.
This video shows you how to make a table saw fence.
FAQs:
What Side Of The Table Saw Should The Fence Be On?
The fence should be on the same side as the blade. This will ensure that the fence is parallel to the blade, essential for accurate cuts.
How Far Away From The Blade Should The Fence Be?
The fence should be a few inches away from the blade. You run the risk that your fingers will get caught between the blade of the fence and it. You won’t be able make precise cuts if it is too far away.
Can I Make Cuts Perpendicular To The Blade?
You can make cuts perpendicular to the blade by using the miter gauge slots on the table saw. Make sure the fence is parallel with the blade.
Can I Make Cuts At An Angle?
Yes, you can make cuts at an angle by using the miter gauge slots on the table saw. Just make sure that the fence is parallel to the blade.
Conclusion:
